JT705A Container Gps Tracking Lock for Cargo Transportation with Remote Unlock
Contact Person : Paul
Phone Number : +86-755-83237778
WhatsApp : +8618145820075
|Minimum Order Quantity :
|USD458 ~ 508 per unit
|Packaging Details :
|Carton: 49cm x 39cm x 31cm
|Delivery Time :
|3 ~ 45 days
|Payment Terms :
|T/T, Paypal, Alipay, etc.
|Supply Ability :
|50,000 per month
|Place of Origin:
|Truck Live Tracking And Cargo Safety
|Real Time Tracking And Authorized Unlcoking
|26500mAh Rechargeable Li-ion Battery
|RFID, Bluetooth, Web, Mobile APP
|BLE Padlock GPS
Bluetooth GPS Intelligent Electronic Lock,
Aluminum GPS Intelligent Electronic Lock,
Truck GPS Smart Bluetooth Padlock
|Based on 2G/4G network communication
|GPS + cell code positioning
|Dual SIM card
|Support two Micro-SIM cards, dual card single standby mode work. The device will automatically select the SIM card for network registration
|Adjustable lock bar length
|To adapt to the lock bar distance of different pitches
|Voice prompts and LED screen
|Different voice prompts in different operating scenarios; LED screen support satellite positioning, communication status, power status, and charging status indication
|DC 5V/ 2A charging
|The battery can be fully charged in about 20 hours
|Internal battery 26500mAh
|Rechargeable lithium battery
|Turn on the spare battery when the main battery is out of power
|Can be used for firmware upgrade, parameter configuration, DEBUG debugging
|Six-axis acceleration sensor
|Motion and vibration detection
|The lock can be unlocked by swiping the RFID authorization card and SMS, configuration tool, mobile Bluetooth APP, and platform sending instructions
|Support static password and dynamic password
|The static password is valid for a long time, and the dynamic password becomes invalid after one use.
|No unlocking function outside the fence
|The lock can only be unlocked in the designated enclosure, by sending instructions or swiping the authorized RFID card to unlock
|10 polygonal electronic fences
|A fence can support up to 10 location nodes
|Support the configuration of 500 authorized RFID cards for unlocking
|Used to configure 500 RFID cards with authorized unlocking
|After sending the unlock instruction, the unlock button is not pressed, and the device will lock automatically after 1min
|Send instructions remotely to restart the device
|Support 5 authorized VIP numbers
|VIP mobile phone number can support SMS command sending, SMS alarm receiving, etc.
Support 8 kinds of alarms
Overtime unlocked alarm
Enter the fence alarm
Leave the fence alarm
Low battery alarm
Back cover open alarm
Swipe illegal card alarm
Password error alarm
|The alarm can be sent to the VIP mobile phone number via short message or sent to the platform via cellular network (such as GPRS/3G/4G network)
|Lock event report
|Unlocking and locking events
|In the tracking mode, the mileage accumulates continuously; in other modes, the accumulated mileage value has a large error, so it is not recommended to refer to it
|When the error between mileage value and actual mileage is large, it can be verified
|The parameters can be configured via Bluetooth, configuration tool, SMS and platform
Blind area supplementary report
Location data and swipe card data are most cached
|Card swiping data and location data are stored in the same area of FLASH
|Support OTA upgrade, serial port upgrade, Bluetooth upgrade
Deep sleep mode
Storage sleep mode
Alarm clock mode
Deep sleep mode: Only allow swiping to unlock, charge, restart the power switch to wake up, communication and positioning modules, do not send data, the default power is less than 5%, then enter the deep sleep mode, the user can configure the remaining power percentage to enter the deep sleep;
Tracking mode: the device continues to work without going to sleep;
Standby mode: sleep by default; when a wake-up condition is detected, the preset data upload time interval will work, during which there is no other wake-up event, then sleep.
Alarm clock mode: upload a piece of data at a preset time point, and up to 12 alarms can be set;
Storage sleep mode: only charging, removing the cover and Bluetooth can wake up
|Device wake-up method
|Prerequisite: The device is in sleep state
Restart the terminal(not configurable to close)
|After power on, wake-up and work for 10 minutes, during which there is no other wake-up source, then sleep.
|Vibration wake-up(can be configured to close)
|After detecting vibration, wake up and work for 10 minutes, during which there is no other wake-up source, then sleep.
|Back cover open(not configurable to close)
|After detecting that the back cover is opened, it wakes up and works for 10 minutes. During this period, there is no other wake-up source, then it sleeps.
|Bluetooth wake-up(not configurable to close)
|Bluetooth connection and send commands, wake up work for 10 minutes, during which there is no other wake-up source, then sleep.
|Connected to external power(not configurable to close)
|When external charging is detected, it wakes up and works for 10 minutes. During this period, there is no other wake-up source, then it sleeps.
Swipe RFID card (not configurable to close)
|Detect swiping RFID card, wake up and work for 10 minutes, during which there is no other wake-up source, sleep.
Short message, phone wake-up(can be configured to close)
(VIP number by default, non-VIP number can be configured)
|Detect short message or dial-up sent by VIP mobile phone number, then wake up and work for 10 minutes, during which there is no other wake-up source, then sleep;
RTC wake-up time(not configurable to close)
|After waking up at a preset time interval and uploading a piece of data, it goes to sleep.
Alarm wake-up(not configurable to close)
|After waking up according to the set alarm clock and uploading a piece of data, it goes to sleep.